China machining solutions provider: | Email: [email protected]Tel: +8618267732328

Gate Valve

Design Standard API, DIN, JIS, GB, API 600, API 602, ANSI
Size range: 1/2"~48", DN15~DN1400
Pressure range: 150LB~2500LB, PN10~PN420
Body materials: Stainless Steel, Carbon Steel, Brass, Bronze, Alloy Steel, Titanium, 904l, Ductile Iron, Cast Iron, Forged Steel, Cast Steel
Type: Knife, Slab, Threaded, Bellow Sealed, Pressure Dsealed, Resilient Seated, Flanged, Steam Jacketed, Cryogenic, Low Tempreature, Moterized, Pneumatic
End Connection: RF, RTJ, BW


The gate valve is a gate with opening and closing parts. The movement direction of the gate is perpendicular to the fluid direction. The gate valve can only be fully opened and closed, and can not be adjusted and throttled. Gate valves are sealed by the contact between the seat and the gate plate. Metal materials are usually surfacing on the sealing surface to increase wear resistance, such as surfacing 1Cr13, STL6, stainless steel, etc. There are rigid gate and elastic gate. According to the difference of gate, gate valves are divided into rigid gate and elastic gate.

Gate Valve Parts

Here you can see the main parts of the gate valve. The disk of a gate valve is also known as a wedge. To learn about each of this part read complete guide of valve parts.

Gate Valve Parts - Gate Valve

Image- Trouvay & Cauvin

Types of Gate Valves

There are three ways to classify the gate valve.

  1. Types of Disk
    1. Solid taper wedge
    2. Flexible wedge
    3. Split wedge or Parallel disks Valve
  2. Types of Body Bonnet Joint
    1. Screwed Bonnet
    2. Bolted-Bonnet
    3. Welded-Bonnet
    4. Pressure-Seal Bonnet
  3. Types of Stem movement
    1. Rising Stem or OS & Y Type (Outside Stem and Screw Type)
    2. Non-rising Stem type

Solid Wedge Gate Valve

Solid wedge is most common & widely used disk types because of its simplicity and strength. A valve with solid wedge may be installed in any position, and it is suitable for almost all fluids. It can be used in turbulent flow also.

However, it does not compensate for changes in seat alignment due to pipe loads or thermal expansion. So, this type of disk design is most susceptible to leakage. Solid wedge is subjected to thermal locking if used in high-temperature service.

Thermal locking is a phenomenon in which wedge is stuck between the seats due to the expansion of the metal. Solid-wedge gate valves are generally used in moderate to lower pressure-temperature applications.

solid wedge gate valve 1 - Gate Valve

Image – Velan

Flexible Wedge Gate Valve

The flexible wedge is a one-piece solid disk with a cut around the perimeter. These cuts vary in size, shape, and depth. A shallow, narrow cut on wedge perimeter gives less flexibility but retains strength. A cast-in recess or deeper and wider cut on wedge perimeter gives more flexibility but compromises the strength.

This design improves seat alignment and offers better leak tightness. It also improved performance in situations where thermal binding possible. Flexible wedges Gate valves are used in steam systems.

Thermal expansion of steam line sometime causes distortion of valve bodies which may lead to thermal blinding. The flexible gate allows the gate to flex as the valve seat compresses due to thermal expansion of steam pipeline and prevent thermal blinding.

The disadvantage of flexible gates is that line fluid tends to collect in the disk. These may result in corrosion and ultimately weaken the disk.

flexible wedge gate valve - Gate Valve

Split wedge or Parallel disks Gate Valve

Split wedge Disk consists of two solid pieces and holds together with the help of special mechanism. You can see the same in images. In case, one-half of the disk is out of alignment; the disk is free to adjust itself to the seating surface. The split disk can be in a wedge shape or a parallel disk type.

Parallel disks are spring loaded, so they are always in contact with seats and give bi-directional sealing. Split wedge is suitable for handling noncondensing gasses and liquids at normal and high temperature.

Freedom of movement of the disk prevents thermal binding even though the valve may have been closed when a line is cold. This means when a line is get heated by fluid and expand it does not create thermal blinding.

Split Wedge Parallel disks Gate Valve - Gate Valve

Types of gate valve based on body, bonnet connection

types of gate valves 1024x346 - Gate Valve

1st is screwed bonnet: This is the simplest design available and it is used for inexpensive valves.

2nd is bolted-bonnet: This is the most popular design and used in a large number of gate valves. This requires a gasket to seal the joint between the body and bonnet.

3rd is Welded-Bonnet: This is a popular design where disassembly is not required. They are lighter in weight than their bolted-bonnet counterparts.

4th one is Pressure-Seal Bonnet: This type is used extensively for high-pressure high-temperature applications. The higher the body cavity pressure, the greater the force on the gasket in a pressure -seal valve.

OS & Y Gate Valve or Rising Stem (Outside Stem and Screw Type)

OS Y Gate Valve Rising Stem 1024x559 - Gate Valve

For a rising stem valve, the stem will go up while opening the valve and move down when you close the valve. You can see in the image. In inside screw design, the threaded portion of the stem is in contact with the flow medium and when you open the valve, handwheel rise with the stem. Whereas in the case of outside screw design, the only smooth portion is exposed to the flow medium and stem will rise above the handwheel. This type of valve is also known as OS & Y valve.  OS & Y means outside steam and York.

Non-rising Stem Gate Valve or Insider Screw Valve

Non rising stem gate valve 1024x497 - Gate Valve

There is no upward movement of the stem in a non-rising stem type. The valve disk is threaded internally. The disc travels along the stem like a nut when the stem is rotated. You can see the image. In this type of valve, stem threads are exposed to the flow medium. Therefore, this design is used where space is limited to allow linear stem movement, and the flow medium does not cause erosion, corrosion, or wear and tear to stem material.  This type of valve also known as insider screw valve.

Gate Valve Applications

  • Gate valves are used in almost all fluid services such as air, fuel gas, feedwater, steam, lube oil, hydrocarbon, and all most any services.
  • Some special gate valve is used in slurry and powder product also such as knife gate valve

Advantages of Gate Valve

  • Gate valve provides good
  • Pressure drop during operation is very less.
  • Most of the gate valve can be used as bi-directional
  • They are suitable for high pressure and temperature application and required less maintenance

Disadvantage of Gate Valve

  • It cannot be used to control the flow.
  • A gate valve is slow in operation. Opening and closing take times which is good also as it reduces the chance of hammering.
  • When partially open it creates vibration and noise.
  • Repairs, such as lapping and grinding of seats are more difficult due to limited access.
Inquery now



Chat via Whatsapp
Email me
Mail to us
Wechat: 8618267732328